Concrete Quantity Calculator
Concrete volume and order volume for slabs, footings, walls, beams and columns, with overage and optional bags.
Runs on your device Processed locally in your browser. Nothing is uploaded.
Bricks to order for a wall, with doors and windows deducted, brick size, mortar joint and wastage allowance.
Use actual solid-brick dimensions and specified joints. Bond, cuts and plaster remain explicit assumptions. Artwork is illustrative. This is an independent reference prototype, not a production engine or certified engineering design.
Results are provided for guidance. Check them against the applicable rules and your professional judgement before relying on them.
This brickwork calculator works out how many bricks to order for a wall — a practical brick quantity calculator for site engineers, contractors, masons, and quantity surveyors planning a brick wall.
Everything is kept at full precision until the end, and each result is shown at a practical precision: areas to 2 decimal places, the calculated count to 2 decimal places, and the order quantity as a whole number.
Unit conversions are exact: 1 mm = 0.001 m, 1 cm = 0.01 m, 1 inch = 0.0254 m and 1 foot = 0.3048 m, so the same wall entered in feet and inches or in metres and millimetres gives the same brick count.
Assumptions you can see and change. The mortar joint (10 mm, about ⅜ in, by default), the number of skins and the wastage allowance all affect the result, so each one is listed under the result as an assumption. None of them is a universal standard — use your own brick, joint and site practice.
This calculator gives brick count only. It does not calculate structural design, reinforcement, bond patterns, labour cost, the cement/sand mortar material breakup, a bill of quantities (BOQ), or a final billing quantity.
A 5 × 3 m wall with one 0.9 × 2.1 m door and two 1.2 × 1.2 m windows, single skin, India modular brick (190 × 90 mm face) with a 10 mm joint, and a 5% wastage allowance:
| Input | |
|---|---|
| Wall unit | m |
| Wall length | 5 |
| Wall height | 3 |
| Number of identical walls | 1 |
| Wall thickness | ½ brick |
| Brick unit | mm |
| Brick length | 190 |
| Brick height | 90 |
| Mortar joint | 10 |
| Wastage allowance % | 5% |
| Result | |
| Bricks to order (rounded up) | 538 |
| Calculated bricks before wastage | 511.50 |
| Wastage allowance | 5% |
| Wastage allowance (bricks) | 25.58 |
| Net wall area (m²) | 10.23 |
| Gross wall area (m²) | 15.00 |
| Openings deducted (m²) | 4.77 |
Enter the wall's length and height, your brick's face size and the mortar joint. The calculator divides the net wall area by the area of one brick plus its joint, multiplies by the number of skins, adds your wastage allowance and rounds up to a whole brick.
Add each opening as its own row with width, height and quantity — for example one door and two identical windows. The total is deducted from every identical wall before the bricks are counted.
It depends on the brick face size and the joint: for a 190 × 90 mm face with a 10 mm joint it is 1 ÷ (0.2 × 0.1) = 50 bricks per square metre per skin. Brick sizes vary by region and manufacturer, so use your own brick rather than a generic figure.
10 mm (about ⅜ in) is a common starting value and the default here, but it is not universal. Enter the joint your mason actually uses; set it to 0 for a brick-size-only count.
The order quantity adds your wastage allowance and rounds up, because you cannot buy part of a brick. The calculated count before wastage is shown alongside it so you can check the arithmetic.
No. This is an estimation aid for planning and quantity checks, not a final billing quantity or a certified bill of quantities. Brick sizes, mortar thickness, wall bonds, site cutting, breakage, and measurement rules vary — verify brick sizes, wall thickness, openings, mortar joints, and wastage before purchase or construction, and confirm the final figures with a licensed engineer, architect, contractor, mason, or professional quantity surveyor.
No. This calculator estimates brick count only. Mortar materials depend on mix, joint and site practice, and are not calculated here.