Excavation Calculator

Runs on your device Processed locally in your browser. Nothing is uploaded.

Excavation volume for a rectangular or circular pit, shaft, trench or footing, with optional swell and truck loads.

Excavation Dimensions & Soil

Soil, bulking & truck basis

Cost Estimate Optional · edit rates

Your entered rates only. Zero rates add no cost. Currency changes the label; amounts are not converted. No live prices or FX.

Line amounts round to 2 decimal places; the total sums those lines. Cost uses calculated quantities before display rounding.

Soil factors & planning notes

Soil factors & planning notes

Soil names are editable estimation examples, not a geotechnical classification or a safe-slope recommendation.

Multiple sections & measurement notes

Multiple sections & measurement notes

Add separate non-overlapping measured sections below. Custom areas use the prismoidal method; do not approximate a safety design from the illustration.

Additional vertical sections

SectionLengthWidthDepthQty

Excavation section · material states

Illustrative material view
Realistic excavation material illustration; geometry is illustrative

Results Summary

Calculated

Calculation Details

Important Notes / Warnings

Volume and haul planning only—not excavation safety, slope approval, shoring or protective-system advice. Artwork is illustrative. This is an independent reference prototype, not a production engine or certified engineering design.

Tool information

Disclaimer

Results are provided for guidance. Check them against the applicable rules and your professional judgement before relying on them.

How to use

This excavation calculator works out earthwork volume for a rectangular pit, circular pit or shaft, trench, or footing pit — common shapes used for everyday earthwork quantity checks.

  1. Choose the excavation type and the unit your dimensions are in. Changing the unit converts the values you already typed.
  2. For a rectangular excavation, enter length, width, and depth. For a circular pit or shaft, enter diameter and depth. Then enter how many identical excavations there are.
  3. Optionally enter a swell percentage to see the loose volume of the dug soil (0% shows bank volume only).
  4. Optionally enter the usable volume one truck carries on your job to see truck loads.
  5. Choose 2, 3, or 4 decimal places for volume results and the swell percentage. Read the bank (in-place) volume, loose volume and whole truck loads when used, then copy or print the result.

Method

  • Bank volume = length × width × depth × number of pits or trenches — the geometric volume of the hole, shown on its own.
  • Circular bank volume = π × (diameter² ÷ 4) × depth × number of circular pits or shafts.
  • Loose volume = bank volume × (1 + swell % ÷ 100), only when you set a swell percentage.
  • Truck loads = loose volume (or bank volume when swell is 0%) ÷ your usable truck volume, rounded up to whole loads.

Unit conversions are exact: 1 mm = 0.001 m, 1 cm = 0.01 m, 1 inch = 0.0254 m and 1 foot = 0.3048 m, so 1 ft³ = 0.028316846592 m³ and 1 yd³ = 0.764554857984 m³ exactly. Volumes are kept at full precision and rounded only for display using your 2, 3, or 4 decimal-place selection. That selection also sets the accepted decimal precision for the swell percentage; it does not alter existing values or the formula.

Bank volume vs. loose volume. Bank volume is the size of the hole itself. Once dug, soil no longer packs as tightly, so the same soil occupies more space; that is the loose volume you haul. Swell varies by soil type and moisture content, so it is an approximate estimate you set — not an engineering constant — and it is listed with the result whenever it is used.

Truck capacity is yours to enter. Trucks carry very different usable volumes, so the calculator never assumes one.

This calculator gives geometric volume only, for vertical-sided rectangular or circular excavations. It does not cover side slopes or battered excavation, slope stability, shoring design, excavation safety compliance, dewatering, geotechnical design, disposal cost, or backfill compaction.

Worked example

A 20 × 0.6 × 1 m trench with a 25% swell estimate and trucks carrying 6 m³ per load:

Input
Excavation type Trench
Unit m
Length 20
Width 0.6
Depth 1
Same-size excavations 1
Swell / bulking % 25%
Usable truck volume 6
Truck volume unit m³
Result
Bank (in-place) excavation volume (m³) 12.000
Bank (in-place) excavation volume (yd³) 15.70
Bank (in-place) excavation volume (ft³) 423.78
Swell used 25%
Loose volume after swell (m³) 15.000
Loose volume after swell (yd³) 19.62
Truck loads (rounded up) 3
Same-size excavations 1

References

  • Rectangular-prism volume: length × width × height (SI, general geometry).
  • Circular-cylinder volume: π × diameter² ÷ 4 × depth (general geometry).
  • International yard and pound agreement (1959): 1 inch = 25.4 mm and 1 foot = 304.8 mm exactly.

FAQ

How do I calculate trench excavation volume?

Choose "Trench", enter the trench's length, width, and depth in one unit, and the number of identical trench runs. A trench uses the same length × width × depth formula as a pit.

How do I calculate footing excavation quantity?

Choose "Footing pit" and enter the pit's length, width, and depth. The excavation type changes only the label, not the arithmetic.

How do I calculate a circular pit or shaft?

Choose "Circular pit / shaft", then enter its diameter, depth, and the number of identical excavations. The calculator uses π × (diameter² ÷ 4) × depth × quantity and keeps the full result precision internally.

What is the difference between bank and loose volume?

Bank volume is the excavation as measured in the ground. Loose volume adds swell, since dug soil takes up more space. Use bank volume to describe the excavation and loose volume when estimating material to move or haul.

What swell percentage should I use?

It depends on the soil and its moisture, and published figures vary. Use a figure from your site investigation, contractor or supplier, and treat the result as an estimate. Leave it at 0% to see bank volume only.

How many truck loads will I need?

Enter the loose volume one truck actually carries on your job. The calculator divides the loose volume by it and rounds up to whole loads.

Can I use this for final billing?

No. This is an estimation aid for planning and quantity checks, not a final billing quantity or a certified bill of quantities. Actual site quantities can differ due to soil conditions, over-excavation, side slopes, shoring, compaction, and local measurement rules — verify quantities before excavation, purchase, billing, or construction, and confirm the final figures with a licensed engineer, architect, contractor, or professional quantity surveyor.